第2个回答 2019-11-19
First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light + Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.\",\"speak_url\":{\"speak_url\":\"/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=af45c13666c4cfae5258ae40dc4c97c0&query=首先,先说太阳路灯的拥有自身专利的厂 , 潢川利民科技太阳能路灯厂,其太阳能控制器,有自己的专利。而且我在他家购买安装的路灯,质量方面啊,价格方面啊,是同等价格下,相对好的了。建议你也可以到厂根据你的情况定制适合你的太阳能路灯产品,还是蛮不错的厂家。 设置方法: 按键按下持续3s以上数码管开始闪烁,系统进入调节模式,松开按键,每按一次按键,数码管数字会换一个数字,直到数码管显示的数字对上用户从表中所选模式对应的数字为止,等数码管停止闪烁或是再次按下按键3s以上即完成设置。 模式介绍 : 纯光控 (0 ):当没有阳光时,光强降至启动点,控制器延时10分钟确认启动信号后,根据设置参数开通负载,负载开始工作;当有阳光时,光强升到启动点,控制器延时10分钟确认关闭信号后关闭输出,负载停止工作。光控 时控 (1 ~ 4):启动过程与纯光控相同,当负载工作到设定时间就自动关闭,设置时间1 ~ 14小时。 手动模式 (5):该模式下用户可以通过按键控制负载的打开与关闭,而不管是否在白天或是晚上。此模式用于一些特殊负载的场合或是调试时使用。 调试模式 (6):用于系统调试时使用,有光信号时即关闭负载,无光信号开通负载,方便安装调试时检查系统安装的正确性。 常开模式(7):上电负载一直保持输出状态,此模式适合需要24小时供电的负载。\",\"tSpeak_url\":\"/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=07d9fc29d83bf7ad60604b982bc7de83&query=First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.","speak_url":{"speak_url":"/audiofrom=en&to=zh&voice=2&cate=speakUrl&key=53d104ba83739a10f1105bc59d3317d9&query=First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.\",\"speak_url\":{\"speak_url\":\"/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=af45c13666c4cfae5258ae40dc4c97c0&query=首先,先说太阳路灯的拥有自身专利的厂 , 潢川利民科技太阳能路灯厂,其太阳能控制器,有自己的专利。而且我在他家购买安装的路灯,质量方面啊,价格方面啊,是同等价格下,相对好的了。建议你也可以到厂根据你的情况定制适合你的太阳能路灯产品,还是蛮不错的厂家。 设置方法: 按键按下持续3s以上数码管开始闪烁,系统进入调节模式,松开按键,每按一次按键,数码管数字会换一个数字,直到数码管显示的数字对上用户从表中所选模式对应的数字为止,等数码管停止闪烁或是再次按下按键3s以上即完成设置。 模式介绍 : 纯光控 (0 ):当没有阳光时,光强降至启动点,控制器延时10分钟确认启动信号后,根据设置参数开通负载,负载开始工作;当有阳光时,光强升到启动点,控制器延时10分钟确认关闭信号后关闭输出,负载停止工作。光控 时控 (1 ~ 4):启动过程与纯光控相同,当负载工作到设定时间就自动关闭,设置时间1 ~ 14小时。 手动模式 (5):该模式下用户可以通过按键控制负载的打开与关闭,而不管是否在白天或是晚上。此模式用于一些特殊负载的场合或是调试时使用。 调试模式 (6):用于系统调试时使用,有光信号时即关闭负载,无光信号开通负载,方便安装调试时检查系统安装的正确性。 常开模式(7):上电负载一直保持输出状态,此模式适合需要24小时供电的负载。\",\"tSpeak_url\":\"/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=07d9fc29d83bf7ad60604b982bc7de83&query=First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.","tSpeak_url":"/audiofrom=en&to=zh&voice=2&cate=tSpeakUrl&key=53d104ba83739a10f1105bc59d3317d9&query=First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.\",\"speak_url\":{\"speak_url\":\"/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=af45c13666c4cfae5258ae40dc4c97c0&query=首先,先说太阳路灯的拥有自身专利的厂 , 潢川利民科技太阳能路灯厂,其太阳能控制器,有自己的专利。而且我在他家购买安装的路灯,质量方面啊,价格方面啊,是同等价格下,相对好的了。建议你也可以到厂根据你的情况定制适合你的太阳能路灯产品,还是蛮不错的厂家。 设置方法: 按键按下持续3s以上数码管开始闪烁,系统进入调节模式,松开按键,每按一次按键,数码管数字会换一个数字,直到数码管显示的数字对上用户从表中所选模式对应的数字为止,等数码管停止闪烁或是再次按下按键3s以上即完成设置。 模式介绍 : 纯光控 (0 ):当没有阳光时,光强降至启动点,控制器延时10分钟确认启动信号后,根据设置参数开通负载,负载开始工作;当有阳光时,光强升到启动点,控制器延时10分钟确认关闭信号后关闭输出,负载停止工作。光控 时控 (1 ~ 4):启动过程与纯光控相同,当负载工作到设定时间就自动关闭,设置时间1 ~ 14小时。 手动模式 (5):该模式下用户可以通过按键控制负载的打开与关闭,而不管是否在白天或是晚上。此模式用于一些特殊负载的场合或是调试时使用。 调试模式 (6):用于系统调试时使用,有光信号时即关闭负载,无光信号开通负载,方便安装调试时检查系统安装的正确性。 常开模式(7):上电负载一直保持输出状态,此模式适合需要24小时供电的负载。\",\"tSpeak_url\":\"/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=07d9fc29d83bf7ad60604b982bc7de83&query=First, let's start with the Solar Street lamp factory, which has its own patent, the Limin Technology Solar Street light factory in Huangchuan, which has its own patent for its solar controller. Moreover, the street lamps I bought and installed at his home are relatively good in terms of quality, AH, and price, AH, at the same price. I suggest you can also go to the factory according to your situation to customize your solar street light products, or pretty good manufacturers. Setting method: Press the key to continue 3s above the digital tube start flashing, the system into adjustment mode, release the key, each press the key, the digital tube number will change a number, until the number displayed by the Nixie tube corresponds to the number of the mode selected by the user from the table, the Nixie tube will stop flashing or press the key 3s or more to complete the setup. Mode description: Pure Light Control 0: When there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the starting signal, according to the setting parameters to turn on the load, the load starts to work; when there is sunlight, the light intensity rises to the starting point, the controller delays 10 minutes to confirm the turn-off signal and then turns off the output and the load stops working. Light Time Control 1 ~ 4 : Start Process and pure light control the same, when the load work to set time to automatically close, set time 1 ~ 14 hours. Manual Mode 5 : This mode allows the user to control the load on and off by pressing a key, whether during the day or night. This pattern is used for special load situations or during debugging. DEBUG MODE 6 : For System debugging, light signal when the load is turned off, no light signal to turn on the load, to facilitate the installation and debugging of the system to check the correctness of installation. Normally open mode (7 : The load is always output, this mode is suitable for the load that needs 24-hour power supply.