汉译英在线翻译句子

Question

1． 电源开关
功能是接通/断开控制器工作电源。
2． 振幅调节器
用于对控制波形的占空比进行调节，功能是在一定范围内改变镀件振动幅度，对镀件转速起微调整功能。
3． 振速调节器
用于对控制波形的频率进行调节，功能主要是调整镀件转速。
4． 保险座
10A――输出DC保险座，用于电流过大时保护元器件用。
5． 六位接线端子
输入供电源，同时输出控制信号去振镀机。
6． 六位接线端子外部接线示意图如图（D）。

五．操作说明
1．确保振镀机电源输入线正确，供电电源正常，振镀可靠固定在支架上；
2．第一次使用时，应将振幅与振速调节器的刻度都调至0。
3．将电源开关POWER扳至ON状态。
4．配合调节速度与振幅调节电位器，使镀件运动速度处于设定/最佳状态进行持续振镀。
备注：在调节速度与振幅调节电位器时，要先将电位器边上的小黑色体，（称为“锁定电位器设定值”键），逆时针方向拔至设定状态，然后方可对电位器进行设定及调节。调节正常后，要把“锁定电位器设定值“键顺时针方向拔向锁定状态，以保证其不会出技术上的差错，否则，因设定参数的漂移会对产品的质量造成不良影响，严重时会到使振镀机损坏。
5．关机/或停止振镀时直接将电源开关POWER拨至OFF位，切断控制器电源即可。

六．故障检测
1． 无振动，且电源开关POWER指示灯不亮。
处理方法：是否有电源；DC保险丝是否烧断。
2． 无振动，但电源开关POWER指示灯亮。
3． 处理方法：1）检查振幅调节器的刻度是否大于4。
2）检查电子板，元件及接线是否有松、断。
3）检查输出控制信号连接线是否断路。
其它事项：请参考振镀机机械说明部分

七． 注意事项
1． 严禁控制器在没关电情况下拨除各接点插口；
2． 严禁电位器末开锁情况下调节电位器；
3． 出现异常故障不能排除时，应及时通知专业人员进行维修操作。

图D六位端子接线示意图
五．操作说明
1．确保振镀机电源输入线正确，供电电源正常，振镀可靠固定在支架上；
2．第一次使用时，应将振幅与振速调节器的刻度都调至0。
3．将电源开关POWER扳至ON状态。
4．配合调节速度与振幅调节电位器，使镀件运动速度处于设定/最佳状态进行持续振镀。
备注：在调节速度与振幅调节电位器时，要先将电位器边上的小黑色体，（称为“锁定电位器设定值”键），逆时针方向拔至设定状态，然后方可对电位器进行设定及调节。调节正常后，要把“锁定电位器设定值“键顺时针方向拔向锁定状态，以保证其不会出技术上的差错，否则，因设定参数的漂移会对产品的质量造成不良影响，严重时会到使振镀机损坏。
5．关机/或停止振镀时直接将电源开关POWER拨至OFF位，切断控制器电源即可。

六．故障检测
1． 无振动，且电源开关POWER指示灯不亮。
处理方法：是否有电源；DC保险丝是否烧断。
2． 无振动，但电源开关POWER指示灯亮。
3． 处理方法：1）检查振幅调节器的刻度是否大于4。
2）检查电子板，元件及接线是否有松、断。
3）检查输出控制信号连接线是否断路。
其它事项：请参考振镀机机械说明部分

七． 注意事项
1． 严禁控制器在没关电情况下拨除各接点插口；
2． 严禁电位器末开锁情况下调节电位器；
3． 出现异常故障不能排除时，应及时通知专业人员进行维修操作。

Answer 1

1. Power Switch
Function is on / off controller working power source.
2. Amplitude modulator
Is used to control the waveform duty cycle to regulate its function is within a certain range to change the vibration amplitude plating on the plating speed from micro-adjustment feature.
3. Velocity regulator
Waveform is used to control the frequency of adjustment, the main function is to adjust speed plating.
4. Insurance Block
10A - Output DC insurance seat, when the overcurrent protection for the components used.
5. 6 terminals
Input for the power supply, while the output control signals to the vibration plate machine.
6. Wiring diagram of the external terminals 6 Figure (D).

五. Instructions
1. Ensure that the vibration plate machine power input line is correct, the normal power supply, reliable, vibration plate fixed to the scaffold;
2. For the first time use, should be amplitude and velocity regulator scale are transferred 0.
3. POWER pull the power switch to the ON state.
4. With adjustable speed and amplitude adjustment potentiometer, so that plating velocity in the setting / best condition for continuous vibration plate.
Note: in the regulation of speed and amplitude adjustment potentiometer, the first edge of the potentiometer a small black body, (called "lock potentiometer settings" button), counter-clockwise to set the drawing state, before they can be carried out on the potentiometer setting and regulation. Adjust to normal, we should "lock potentiometer settings" button in a clockwise direction pulling the lock to ensure that it does not out technical errors, otherwise set the parameters of the drift due to the quality of products would be adversely influence, and in severe damage to the machine so that vibration plate.
5. Shutdown / or stop the vibration plate when the POWER dial directly to the power switch to the OFF position, cut off the power supply controller can be.

六. Fault Detection
1. No vibration, and the power switch POWER indicator light does not shine.
Approach: Are there any power supply; DC fuse is blown.
2. No vibration, but the power switch POWER indicator light.
3. Approach: 1) Check the scale of the amplitude modulator is greater than 4.
2) Check the e-board, components, and whether there is loose wiring, broken.
3) Check the output control signal cable is open circuit.
Other matters: Please refer to the narrative part of mechanical vibration plate machine

7. Notes
1. The controller is strictly prohibited without customs of electricity allocated among the various contact socket;
2. Potentiometer is prohibited under the late unlocking adjustment potentiometer;
3. Abnormal failure can not be excluded, it shall promptly notify the professional staff carry out maintenance operations.

Figure D 6 terminal wiring diagram
五. Instructions
1. Ensure that the vibration plate machine power input line is correct, the normal power supply, reliable, vibration plate fixed to the scaffold;
2. For the first time use, should be amplitude and velocity regulator scale are transferred 0.
3. POWER pull the power switch to the ON state.
4. With adjustable speed and amplitude adjustment potentiometer, so that plating velocity in the setting / best condition for continuous vibration plate.
Note: in the regulation of speed and amplitude adjustment potentiometer, the first edge of the potentiometer a small black body, (called "lock potentiometer settings" button), counter-clockwise to set the drawing state, before they can be carried out on the potentiometer setting and regulation. Adjust to normal, we should "lock potentiometer settings" button in a clockwise direction pulling the lock to ensure that it does not out technical errors, otherwise set the parameters of the drift due to the quality of products would be adversely influence, and in severe damage to the machine so that vibration plate.
5. Shutdown / or stop the vibration plate when the POWER dial directly to the power switch to the OFF position, cut off the power supply controller can be.

六. Fault Detection
1. No vibration, and the power switch POWER indicator light does not shine.
Approach: Are there any power supply; DC fuse is blown.
2. No vibration, but the power switch POWER indicator light.
3. Approach: 1) Check the scale of the amplitude modulator is greater than 4.
2) Check the e-board, components, and whether there is loose wiring, broken.
3) Check the output control signal cable is open circuit.
Other matters: Please refer to the narrative part of mechanical vibration plate machine

7. Notes
1. The controller is strictly prohibited without customs of electricity allocated among the various contact socket;
2. Potentiometer is prohibited under the late unlocking adjustment potentiometer;
3. Abnormal failure can not be excluded, it shall promptly notify the professional staff carry out maintenance operations.

Answer 2

Abstract:
With
today's
scientific
and
technological
development,
new
technology
and
modern
educational
methods
widely
used
in
the
continuous
updates,
multimedia
technology
began
to
allow
the
entry
of
Track
and
Field
classrooms.
Multimedia
technology
into
the
teaching
track
and
field
class,
has
many
advantages:
to
improve
the
traditional
education
model;
give
full
play
to
the
teaching
open;
students
motivation
to
learn;
stimulate
student
interest
in
learning.
Dan
in
the
actual
operation
of
them,
that
we
should
pay
attention
to,
not,
for
the
multimedia
and
application
of
multimedia,
multimedia
application
to
Wei
quality
education
services;
to
autonomy
of
students,
creative
learning
services;
to
the
opening
teaching
service.
自己在检查下！

Answer 3

i’mgoingoutshopping,andwon’tbebackuntilabout5:00pm.ihavetakenwithmethetwobooksyouaskedmetoreturntothecitylibrary.atabout1o’clockthisafternoon,tracycalled,sayingthatshecouldn’tmeetyouatboltoncoffeetomorrowmorningasshehassomethingimportanttoattendto.shefeltverysorryaboutthat,butsaidthatyoucouldsetsomeothertimeforthemeeting.shewantedyoutocallherbackassoonasyouarehome.shehasalreadytoldsusanaboutthischange.

Answer 4

Each
year,
all
live
without
valentine
on
the
Valentine's
Day!

Answer 5

Every
year,
is
not
the
lover's
valentine's
day!